How To Repair The Drive Motor Crosley Record Player

Vinyl records are outset to have a huge surge in popularity again. In that location is a whole generation of immature people who don't even know what a vinyl record is allow alone know how to prepare a record player that is non spinning.

In that location are basically two different types of spinning platter tape players.

Directly Drive which has the drive motor directly continued to the platter.
Belt Drive which has the platter continued to the drive motor via a rubber belt.

Many erstwhile vinyl tape players from the 1960s and earlier are a work of art and notwithstanding function today. The main problem I come beyond with early on record players are the drive belts are usually worn or cleaved.

People then throw them out or give them abroad to their local Goodwill store where someone with a little bit of knowledge can gear up them right upward.

Tabular array of Contents

one How to supplant the chugalug on a vinyl tape player.
- one.1 How to remove turntable platter
- ane.ii Replacing the turntable platter
two Straight Drive turntable not spinning.
3 DIY Turntable belt alternative
4 Conclusion

How to replace the belt on a vinyl tape player.

Nearly record players have easily removable platters. The tape platter is the round spinning disk that the vinyl tape will rotate on. Some platters will take access holes and some will require access from underneath.

These like shooting fish in a barrel instructions are for my Auna TT-931 turntable but they will piece of work for 99% of all turntables that take an internal bulldoze belt.

How to remove turntable platter

How to Fix a Record Player not Spinning — Remove the cir-clip using a screwdriver.

Plow off and unplug the record thespian from the mains ability for prophylactic.
Start by taking off the platter past either removing a circlip on the top or a screw from underneath. Exist careful with circlips as they tin can bound off. Use a pocket-sized screwdriver to gently prise it off.

Spin the turntable past mitt to align up the drive motor with the access hole in the record player tabular array. If the record player platter is still connected to the drive motor use your fingers or a pencil to gently remove the drive belt from the motor. Some turntable platters accept admission holes that make life easy. Otherwise, you lot will accept to remove the base of the tape player.

auna TT-931 drive belt replacement procedure

Measure the platter bore to work out the belt size that you lot will demand. If you even so have admission to the old chugalug you lot can too mensurate chugalug width, thickness, length, and circumference. Be aware if the belt has stretched, you may get an incorrect measurement.

measure turntable platter for drive belt

Replacing the turntable platter

Basically its the reverse of taking one off but with the added step of putting the rubber turntable belt dorsum onto the platter and the bulldoze motor. While the vinyl turntable disk is off its a great time to lubricate any gears and springs. I like to use SuperLube Synthetic Grease.

inside a turntable with the record platter removed — Record platter removed.

With platters that accept admission holes, I outset identify the chugalug onto the platter and so use my finger to stretch the rubber ring onto the drive motor. You can now push downward the platter fully onto the turntable base of operations.

Use the circlip to secure the vinyl platter to the turntable and spin it by hand to make sure everything moves freely. Twists in the belt are a large problem to make sure that the belt is tight and untwisted. You tin at present give information technology a dry out run without any records on the turntable.

replace the turntable cir-clip with pliers — Don't forget the cir-clip

Exist sure to terminate upwardly by making sure that the tape actor turntable platter is level and runs truthful. It should exist placidity and not rubbing on any parts of the turntable. Wobbles are bad and need to be rectified quickly before impairment is caused to the turntable and vinyl records.

The video beneath shows how to change the drive belt on a Crosley turntable. It should only have you a few minutes.

Straight Drive turntable non spinning.

Straight drive turntables are a lot harder to diagnose and set. This is because they don't have hands replaceable parts. Some of the quick fixes that may cause the motor to finish spinning are.

Loss of power, bank check the internal fuse and that the power leads are still connected.
Straight bulldoze motor has dirt, fluff or pilus wrapped around the shaft.
Turntable platter is jammed upward against the edge of the casing.
The drive motor has failed and volition require a new part.
Auto beginning limit switch on the pickup arm has been damaged or failed.

Each of these problems and solutions is a starting point for a record player that is not spinning so you will need some basic troubleshooting skills. Only if I can do it everyone can.

DIY Turntable belt alternative

For a quick prepare to see if everything else is working you can employ rubber bands or dental floss. Make certain not to put too much stress onto the motor by using an undersized rubber band.

Dental floss works great with adjustable motor mounts and then you can get the correct tension. Be mindful this is but a quick test to check all of the other components of the turntable.

Cycle inner tubes cutting to size and glued using patch glue also can work to make a turntable belt. Use the patch to gum both ends together with the patch on the outside of the rubber ring.

Thin flexible o-rings can also work if information technology is very close to the correct size. Try an auto parts store for something that may fit.

Conclusion

Finding an sometime tape player that is not spinning and restoring it back to life is a very rewarding experience. In gild today we throw out too many items that break down. If you are into vinyl records sooner or afterward you will take to open up your turntable and do some basic maintenance.

Some of these old turntables are becoming very valuable. One that is working is worth even more. I know people who merely go to garage sales to buy sometime records and turntables. With a belt replacement and a new stylus, they are now selling on eBay for hundreds of dollars. For a practiced idea on the value on some old vinyl records, Discogs.com is a keen resource.

If y'all have care of your vinyl music automobile information technology will take intendance of your records and your music volition sound fantastic. Don't spend $400 on a new turntable when all it may need is a belt repair.

I also like to supplant the turntable needle on all 2nd-hand units. You never know how old or how damages this stylus is. It is a cheap detail so its amend to be safe than sad is the old needle damages you expensive vintage vinyl records.

Let me know in the comments beneath what you have had to prepare to get an onetime turntable working over again. Don't forget to check out our other DIY repair jobs around the home.

I am a qualified Industrial Electrician for the past xx years and I dearest to share my cognition on home repair jobs.

I love fast toys like Motorcycles, Cars, Jetskis, and Boats then writing about them is easy.
To keeps costs down I do all my own mods, repairs, and servicing. These skills I desire to share with anybody. DIY is a skill everyone can learn.